1
/
2
Σύνδεσμος αγγελίας:
car.gr/55976477
S, 93" KN-series engines. Generator cases
17,74 €
Χαρακτηριστικά
Τίτλος
S, 93" KN-series engines. Generator cases
Κατάσταση
Καινούργιο
Τιμή
17,74 €
Κατηγορία
Ανταλλακτικά Μοτοσυκλετών - Αναβάτη - Άλλα
Εσωτερικός κωδικός καταστήματος
Car-1141538
Εργοστασιακός κωδικός
531588
Κατασκευαστής ανταλακτικού
S&S 
S, 93" KN-series engines. Generator cases
17,74 €
Comes with an FHP420 cam & 8.2 compression ratio. The S KN-series (Knucklehead style) engines come very close to the original but it is not a replica engine. A number of improvements/changes were made. It comes with 48-99 engine mounts and will not fit OEM Knuckle frames. A later, 58-65, style flywheel assembly is used, with the splined sprocket shaft and a Timken sprocket shaft bearing for increased strength. Therefore a 54-65 style tin primary and motorsprocket must be used. Rocker arm cover \'tins\' are also improved over stock. The lower covers are made of die-cast aluminum, and instead of being held in place by the valve guide, they are held down by valve spring pressure. A special gasket on the bottom of the lower \'tin\' provides a good seal and easier access for servicing, since the valve guides do not need to be pressed out in order to remove the lower covers. Instead of the steel brazed-in hard oil return lines used on stock tins, S has improved oil line design for better reliability, access and assembly. Engines come completely assembled and ready to run with an S pre-set Superstock single fire ignition system and S Super E carburetor. Note: Crankcases come with 48-99 engine mounts and will not fit OEM Knuckle frames.
17,74 €
Αρ. αγγελίας:
Χαρακτηριστικά
Τίτλος
S, 93" KN-series engines. Generator cases
Τιμή
17,74 €
Κατάσταση
Καινούργιο
Εσωτερικός κωδικός καταστήματος
Car-1141538
Εργοστασιακός κωδικός
531588
Κατασκευαστής ανταλακτικού
S&S
Τελευταία αλλαγή
1 μήνας πριν
Σύνδεσμος
Περιγραφή
Comes with an FHP420 cam & 8.2 compression ratio. The S KN-series (Knucklehead style) engines come very close to the original but it is not a replica engine. A number of improvements/changes were made. It comes with 48-99 engine mounts and will not fit OEM Knuckle frames. A later, 58-65, style flywheel assembly is used, with the splined sprocket shaft and a Timken sprocket shaft bearing for increased strength. Therefore a 54-65 style tin primary and motorsprocket must be used. Rocker arm cover \'tins\' are also improved over stock. The lower covers are made of die-cast aluminum, and instead of being held in place by the valve guide, they are held down by valve spring pressure. A special gasket on the bottom of the lower \'tin\' provides a good seal and easier access for servicing, since the valve guides do not need to be pressed out in order to remove the lower covers. Instead of the steel brazed-in hard oil return lines used on stock tins, S has improved oil line design for better reliability, access and assembly. Engines come completely assembled and ready to run with an S pre-set Superstock single fire ignition system and S Super E carburetor. Note: Crankcases come with 48-99 engine mounts and will not fit OEM Knuckle frames.
Χώρος Διαφήμισης
Έμπορος
IRON HORSES ΑΝΤΑΛΛΑΚΤΙΚΑ ΑΞΕΣΟΥΑΡ SERVICE HARLEY DAVIDSON
ΚΑΘΗΜΕΡΙΝΑ ΑΝΤΑΛΛΑΚΤΙΚΑ ΑΝΤΙΚΑΤΑΒΟΛΗ ΣΕ ΟΛΗ ΤΗΝ ΕΛΛΑΔΑ ΑΥΘΗΜΕΡΟΝ.
ΠΡΟΣΟΧΗ! ΟΙ ΤΙΜΕΣ ΜΠΟΡΟΥΝ ΝΑ ΜΕΤΑΒΛΗΘΟΥΝ ΧΩΡΙΣ ΕΝΗΜΕΡΩΣΗ ΚΑΝΟΥΜΕ
ΟΤΙ ΜΠΟΡΟΥΜΕ ΓΙΑ ΝΑ ΚΡΑΤΗΣΟΥΜΕ ΕΝΗΜΕΡΩΜΕΝΕΣ ΤΙΣ ΑΓΓΕΛΙΕΣ ΜΑΣ!
Ώρες λειτουργίας:
ΔΕΥΤΕΡΑ ΕΩΣ ΠΑΡΑΣΚΕΥΗ ΑΠΟ ΤΙΣ 10:00 ΕΩΣ ΤΙΣ 18:00 ΚΑΙ ΣΑΒΒΑΤΟ ΑΠΟ ΤΙΣ 10:00 ΕΩΣ ΤΙΣ 14:00